| |
|
WavePro 7 Zi Series
Combining signal fidelity with an architecture that maximizes speed in every performance aspect, the new WavePro 7 Zi Series presents a totally new oscilloscope experience from 1.5 to 6 GHz bandwidths. Experience 50 Ω and 1 MΩ inputs for every channel and four inputs into high-speed front end amplifiers and analog to digital converters. Experience the new X-Stream II architecture that provides 10 to 20 times faster long memory performance than any other oscilloscope. Combined with LeCroy’s flexible and deep analysis toolbox, the WavePro 7 Zi Series gives an unforgettable experience for the debugging, validation, analysis and compliance testing of electronic designs.
- 1.5 GHz to 6 GHz
- X-Stream II streaming architecture — 10–20 times faster than other oscilloscopes
- 15.3" WXGA Widescreen Display
- TriggerScan™ detects and captures more anomalies per second
Freedom from Limitations
 WavePro 7 Zi excels in the way it offers general purpose utility never before seen in oscilloscopes from 1.5 to 6 GHz. All WavePro 7 Zi oscilloscopes contain selectable 50 Ω and 1 MΩ input capability. The 4 and 6 GHz models include both ProBus and ProLink input types which means eight probes can be attached and then multiplexed from the front panel or by remote control. The result— it’s easy to hook up a passive probe even on 4 or 6 GHz models—no more frustration and hassle of trying to find a 1 MΩ input adapter. Plus, any existing investment in LeCroy probes, such as current probes, single-ended or differential active probes, or high voltage probes, is fully leveraged. Perfect.
More Triggers Isolate More Problems More Effectively
A powerful combination of high bandwidth Edge and 10 different SMART triggers allow you to isolate the problem quickly and begin to focus on the cause. Most SMART triggers allow triggering on pulse widths or features as small as 200 ps. A high-speed serial trigger enables triggering on up to 2.7 Gb/s serial patterns of up to 80-bits in length. Built-in hardware clock recovery is also included.
TriggerScan™
 TriggerScan uses high-speed hardware triggering capability with persistence displays to capture only the signals of interest and provide answers up to 100X faster that other methods. Traditional fast display update modes work best on frequent events occurring on slow edge rates while TriggerScan excels in finding infrequent events on fast edge rates.
WaveScan™ Advanced Search and Analysis Finds Problems that Triggers Won’t Find
The best trigger won’t find all unusual events—a more powerful capability is sometimes needed. WaveScan provides the ability to locate unusual events in a single capture (i.e., capture and search) or "scan" for an event in many acquisitions over a long period of time. Select from more than 20 search modes (frequency, rise time, runt, duty cycle, etc.), apply a search condition and begin scanning. When an event is found, WaveScan highlights the error on screen and displays a table listing the errors.
Fully Integrated Mixed Signal Oscilloscope (4+36) Option
 Add Mixed Signal Oscilloscope (MSO) operation using the MS Series mixed signal options. These convenient add-ons connect to the LeCroy LBUS and quickly and simply provide capability to acquire up to 36 digital lines time-correlated with analog waveforms. No time is wasted in trying to learn how to connect, synchronize or operate a complicated logic analyzer since the MSOs are already completely integrated into the scope operation. In addition to acquiring digital lines, they are also helpful for monitoring low-speed signals, such as serial data clock, data, and chip select signals, thus preserving the analog channels for higher speed requirements.
LeCroy — The Acquisition Memory Leader
LeCroy has found a way to make long acquisition memory seamless and pain free to use. The WavePro 7 Zi Series’ proprietary X-Stream II architecture supports capturing, zooming, measuring and analyzing multiple waveforms at 256 Mpts deep. What you experience is performance gains of 10–20X over what is available today. Whether looking at the acquired signal or while analyzing several screens of statistics, tracking a frequency or identifying complex patterns the WavePro 7 Zi is designed to perform.
Instantaneous Responsiveness
The first time you use the Zi oscilloscope you will experience responsiveness that you’ve never seen before. Acquiring and manipulating the longest record lengths and the most complex WaveShape Analysis are all easily handled at the same time. Whether you use the front panel or choose to make adjustments with a mouse or the touch screen, the system performs.
Optimized for Fast Throughput
Designed for long memory operation and responsiveness X-Stream II technology enables high throughput of data—even when the oscilloscope is performing multiple 100 Mpts waveforms. It does so by eliminating the trade-offs between long memory length and quick processing. WavePro 7 Zi’s proprietary architecture design is augmented with an Intel® Core™ 2 Quad processor, high-speed serial data buses, a 64-bit OS and up to 8 GB of RAM.
Optimized for Long Memory
By using variable waveform segment lengths to improve the CPU cache memory efficiency the WavePro 7 Zi is designed for the fastest processing of long waveform records. The result—10-20 times faster processing compared to other oscilloscopes.
Optimized for Responsiveness
By dynamically allocating buffers where to maximize memory availability the WavePro 7 Zi Series embodies the fastest front panel responsiveness. Waveform previewing shows interim calculation results while a built in processing abort make front panel control changes instant by stopping the current process and allowing new waveforms to be positioned or zoomed—all without a lengthy recalculation.
Digital Filter Software Package (WPZi-DFP2)
DFP2 lets you implement Finite or Infinite Impulse Response filters to eliminate undesired spectral components, such as noise, and enhances your ability to examine important signal components. You can choose from a standared set of FIR or IIR filters. You can also design your own filters.
Spectrum Analyzer Analysis Package (WPZi-SPECTRUM)
The spectrum converts the controls of your oscilloscope to those of a spectrum analyzer. Adjust the frequency span, resolution and center frequency. Apply filtering to your signal and watch the frequency signature change in real time. A unique peak search labels the spectral components and presents frequency and level in a table. Touch any line jump to that peak.
Mixed Signal Oscilloscope Option (MS-250/MS-500)
The Mixed Signal option allows the WavePro 7 Zi to convert to a mixed signal oscilloscope with up to 36 digital channels. Channels are sampled at 2 GS/s up to 50 Mpts/Ch. Having up to 36 digital inputs timesynchronized with four analog channels extends the oscilloscope's use to provide a total system view.
Jitter and Timing Analysis Package (WPZi-JTA2)
Specialized timing parameters measure period, cycle-cycle, half period, width, etc. jitter on a variety of signals. Use the three views of jitter (statistical, time, and frequency) to understand root cause and to debug problems. Histograms provide understanding of statistical distributions. Tracks provide a means to show time-correlated peaks of jitter, and compare to other signals. FFTs provide the ability to debug root causes of high in-circuit jitter.
WavePro 715Zi
| Vertical System |
Analog Bandwidth @ 50 Ω (-3 dB)
|
|
1.5 GHz
|
Rise Time (typical)
|
|
235 ps
|
Input Channels
|
|
4
|
Bandwidth Limiters
|
|
20 MHz, 200 MHz
|
Input Impedance
|
|
50 Ω or 1 MΩ||15pF, 10 MΩ || 11 pF with supplied Probe
|
Input Coupling
|
|
1 MΩ: AC, DC, GND; 50 Ω: DC, GND
|
Maximum Input Voltage
|
|
50 Ω: ±5 Vrms
|
Channel-Channel Isolation ProLink Input
|
|
Not Applicable
|
Channel to Channel Isolation ProBus Input
|
|
100:1
|
Vertical Resolution
|
|
8 bits; up to 11 bits with enhanced resolution (ERES)
|
Sensitivity
|
|
50 Ω: 2 mV–1 V/div, fully variable (2-9.99 mV/div via zoom); 1 MΩ: 2 mV–10 V/div, fully variable
|
DC Gain Accuracy
|
|
±1.5% of full scale
|
Offset Range
|
|
50 Ω:
|
Offset Accuracy
|
|
±(1.5% of full scale + 1.0% of offset value + 1 mV)
|
|
| Horizontal System |
Timebases
|
|
Internal timebase common to 4 input channels; an external clock may be applied at the auxiliary input
|
Time/Division Range
|
|
20 ps/div–1000 s/div (RIS mode: 20 ps/div - 10 ns/div; Roll mode: up to 1000 s/div)
|
Clock Accuracy
|
|
< 1 ppm
|
Jitter Noise Floor
|
|
1.5 ps (Typical)
|
Trigger and Interpolator Jitter
|
|
3 psrms (typical)
|
Sample Rate and Delay Time Accuracy
|
|
< 0.06 / SR + (1 ppm * Reading) (rms)
|
Channel-Channel Deskew Range
|
|
±9 x time/div. setting, 100 ms max., each channel
|
External Timebase Reference (Input)
|
|
10 MHz; 50 Ω impedance, applied at the rear input
|
External Timebase Reference (Output)
|
|
10 MHz; 50 Ω impedance, output at the rear
|
External Sample Clock
|
|
0.1 Hz-100 MHz, 50 Ω or 1 MΩ impedance, applied at the auxiliary input
|
|
| Acquisition System |
Single-Shot Sample Rate/Ch
|
|
20 GS/s on 2 Ch
|
Random Interleaved Sampling (RIS)
|
|
200 GS/s for repetitive signals (20 ps/div to 10 ns/div)
|
Maximum Trigger Rate
|
|
1,000,000 waveforms/second (in Sequence Mode, up to 4 channels)
|
Intersegment Time
|
|
1 μs
|
Standard Memory (4 Ch / 2 Ch) (Number of Segments)
|
|
10 M / 20 M
|
S - Memory Option
|
|
32 M / 64 M
|
M - Memory Option
|
|
64 M / 128 M
|
L - Memory Option
|
|
128 M / 256 M
|
|
| Acquisition Processing |
Averaging
|
|
Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps
|
Enhanced Resolution (ERES)
|
|
From 8.5 to 11 bits vertical resolution
|
Envelope (Extrema)
|
|
Envelope, floor, or roof for up to 1 million sweeps
|
Interpolation
|
|
Linear or Sin x/x
|
|
| Triggering System |
Modes
|
|
Normal, Auto, Single, and Stop
|
Sources
|
|
Any input channel, Aux, Aux/10, or line; slope and level unique to each source (except line trigger)
|
Coupling Mode
|
|
DC, AC, HFRej, LFRej
|
Pre-trigger Delay
|
|
0–100% of memory size (adjustable in 1% increments of 100 ns)
|
Post-trigger Delay
|
|
0–10,000 divisions in real time mode, limited at slower time/div settings or in roll mode
|
Hold-off by Time or Events
|
|
From 2 ns up to 20 s or from 1 to 99,999,999 events
|
Internal Trigger Range
|
|
±5 div from center
|
Trigger Sensitivity with Edge Trigger (Ch 1–4) ProBus Inputs
|
|
2 div @ < 1 GHz
|
Trigger Sensitivity with Edge Trigger (Ch 1–4) ProLink Inputs
|
|
Not Applicable
|
External Trigger Sensitivity
|
|
2 div @ < 1 GHz
|
External Trigger Input Range
|
|
Aux (±0.4 V); Aux/10 (±4 V)
|
Max. Trigger Frequency, SMART Trigger
|
|
1.0 GHz @ = 10 mV/div (minimum signal width setting 500 ps)
|
|
| Basic Triggers |
Edge/ Slope/ Line
|
|
Triggers when signal meets slope (positive, negative, or either) and level condition.
|
TV-Composite Video
|
|
Triggers NTSC or PAL with selectable line and field; HDTV (720p, 1080i, 1080p) with selectable frame rate (50 or 60 Hz) and Line; or CUSTOM with selectable Fields (1-8), Lines (up to 2000), Frame Rates (25, 30, 50, or 60 Hz), Interlacing (1:1, 2:1, 4:1, 8:1), or Synch Pulse Slope (Positive or Negative).
|
|
| SMART Triggers |
State or Edge Qualified
|
|
Triggers on any input source only if a defined state or edge occurred on another input source. Delay between sources is selectable by time or events.
|
Dropout
|
|
Triggers if signal drops out for longer than selected time between 1 ns and 20 s.
|
Pattern
|
|
Logic combination (AND, NAND, OR, NOR) of 5 inputs (4 channels and external trigger input). Each source can be high, low, or don’t care. The High and Low level can be selected independently. Triggers at start or end of the pattern.
|
|
| SMART Triggers with Exclusion Technology |
Glitch
|
|
Triggers on positive or negative glitches with widths selectable as low as 500 ps (depending on oscilloscope bandwidth) to 20 s, or on intermittent faults.
|
Width (Signal or Pattern)
|
|
Triggers on positive or negative widths with widths selectable as low as 200ps (depending on oscilloscope bandwidth) to 20 s, or on intermittent faults.
|
Interval (Signal or Pattern)
|
|
Triggers on intervals selectable between 1 ns and 20 s.
|
Timeout (State/Edge Qualified)
|
|
Triggers on any source if a given state (or transition edge) has occurred on another source.
|
Runt
|
|
Trigger on positive or negative runts defined by two voltage limits and two time limits. Select between 1 ns and 20 ns.
|
Slew Rate
|
|
Trigger on edge rates. Select limits for dV, dt, and slope. Select edge limits between 1 ns and 20 ns.
|
"A" Trigger List
|
|
Edge, Window, Width, Glitch, Pattern, Pattern State, State, Dropout, Interval, Runt, Slew Rate, Serial Data (optional I2C, SPI, UART/RS-232, CAN, LIN, FlexRay)
|
"B" Trigger List
|
|
Edge
|
Exclusion Triggering
|
|
Trigger on intermittent faults by specifying the expected behavior and triggering when that condition is not met
|
Holdoff Between Sequential Triggers
|
|
Arming = Serial & Triggering = Anything, then min. time between events defined by serial pattern length
|
|
| Cascade (Sequence) Triggering |
Capability
|
|
Arm on “A” event, then Trigger on “B” event. Or Arm on “A” event, then Qualify on “B” event, and Trigger on “C” event. Or Arm on “A” event, then Qualify on “B” then “C” event, and Trigger on “D” event
|
Types
|
|
A or B event: Edge, Glitch, Width, Window, Dropout, Interval, Runt, Slew Rate, or Pattern (analog) C or D event: Edge or Pattern
|
Holdoff
|
|
Delay between A and B, B and C, C and D, are all selectable by time or number of events
|
Reset
|
|
Reset between A and B, B and C, C and D, are all selectable in time
|
|
| High Speed Serial Protocol Triggering |
Data Rates
|
|
Not available
|
Pattern Length
|
|
Not available
|
Clock and Data Outputs
|
|
Not available
|
Clock Recovery Jitter
|
|
Not available
|
Clock Recovery Tracking/ Acquisition Range
|
|
Not available
|
Hardware Clock Recovery Loop BW
|
|
Not available
|
|
| Low Speed Serial Protocol Triggering (Optional) |
Optionally available
|
|
I2C, SPI (SPI, SSPI, SIOP), UART-RS232, CAN, LIN, FlexRay
|
|
| Color Waveform Display |
Type
|
|
Color 15.3" flat panel TFT-Active Matrix LCD with high resolution touch screen
|
Resolution
|
|
WXGA; 1280 x 768 pixels
|
Number of traces
|
|
Display a maximum of 8 traces. Simultaneously display channel, zoom, memory and math traces.
|
Grid Styles
|
|
Auto, Single, Dual, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y
|
Waveform Representation
|
|
Sample dots joined, or sample dots only
|
|
| Internal Waveform Memory |
Internal Waveform Memory
|
|
4 active waveform memory traces (M1-M4) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity.
|
|
| WaveStream™ Fast Viewing Mode |
Intensity
|
|
256 Intensity Levels, 1–100% adjustable via front panel control
|
Number of Channels
|
|
up to 4 simultaneously
|
Max Sampling Rate
|
|
40 GS/s (20 GS/s for WavePro 710Zi without WPZi-1GHZ-4X20GS option)
|
Waveforms
|
|
up to 2500 Waveforms/ second
|
|
| Automatic Setup |
Auto Setup
|
|
Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals
|
Find Vertical Scale
|
|
Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range
|
|
| Probes |
Probes
|
|
Qty. (4) ÷10 Passive Probes
|
Probe System: ProBus
|
|
Probus (and ProLink on 4-6 GHz models). Automatically detects and supports a variety of compatible probes
|
Scale Factors
|
|
Automatically or manually selected depending on probe used
|
Calibration Output
|
|
1kHz square wave, 1Vp-p (typical), output to probe hook
|
|
| Analog Persistence Display |
Analog and Color-Graded Persistence
|
|
Variable saturation levels; stores each trace’s persistence data in memory
|
Trace Selection
|
|
Activate persistence on all or any combination of traces
|
Sweep Display Modes
|
|
All accumulated, or all accumulated with last trace highlighted
|
Persistence Types
|
|
Select analog, color, or three-dimensional
|
Persistence Aging
|
|
Select from 500 ms to infinity
|
|
| Setup and Waveform Storage |
Front Panel and Instrument Status
|
|
Store to the internal hard drive or to a USB-connected peripheral device.
|
|
| High Speed Digitizer Output (Option) |
Type
|
|
LeCroy LSIB
|
Transfer Rate
|
|
Up to 325 MB/s (Typical)
|
Output Protocol
|
|
PCI Express, Gen 1 (4 lanes utilized for data transfer)
|
Control Protocol
|
|
TCP/IP
|
Command Set
|
|
Via Windows Automation, or via LeCroy Remote Command Set
|
|
| Processor/CPU |
Type
|
|
Intel® CoreTM 2 Quad, 2.5 GHz (or better)
|
Processor Memory
|
|
4 GB standard, up to 8 GB optional
|
Operating System
|
|
Microsoft Windows® Vista Business Edition (64-bit) with SP1
|
Oscilloscope Operating Software
|
|
Entire instrument including any installed optional applications packages operates within a single (X-Stream) Windows application
|
Real Time Clock
|
|
Date and time displayed with waveform an in hardcopy files. SNTP support to synchronize to precision internal clocks.
|
|
| Zoom Expansion Traces |
Zoom Expansion Traces
|
|
Display up to 4 Zoom and 8 Math/Zoom traces
|
|
| Interface |
Remote Control
|
|
Via Windows Automation, or via LeCroy Remote Command Set
|
GPIB Port (optional)
|
|
Supports IEEE – 488.2
|
LSIB Port (optional)
|
|
Supports PCIe Gen1 x4 protocol with LeCroy supplied API
|
USB Device Port (optional)
|
|
Type-B
|
Ethernet Port
|
|
Supports 10/100/1000 BaseT Ethernet interface (RJ45 port)
|
USB Ports
|
|
minimum 6 total (incl. 3 front panel) USB 2.0 ports support Windows compatible devices
|
External Monitor Port
|
|
15-pin D-Type WXGA compatible to support customer-supplied external monitor. DVI connector to support LeCroy Zi-EXTDISP-15 additional touch screen display accessory. Includes support for extended desktop operation with optional LeCroy or other second monitor
|
Serial Port
|
|
2 standard
|
Peripheral Bus
|
|
LeCroy LBUS standard
|
|
| Auxiliary Input |
Signal Types
|
|
Select External Trigger
|
Coupling
|
|
50 Ω: DC; 1 MΩ: AC, DC, GND
|
Max. Input Voltage
|
|
50 Ω: 5 Vrms; 1 MΩ: 250 V (Peak AC < 10 kHz + DC)
|
|
| Auxiliary Output |
Signal Types
|
|
Select from calibrator, control signals or Off
|
Calibrator Signal
|
|
5 Hz–5 MHz square wave or DC level; 0.0 to 500 mV into 50 Ω (0–1 V into 1 MΩ)
|
Control Signals
|
|
Trigger enabled, trigger out, pass/fail status
|
|
| General |
Auto Calibration
|
|
Ensures specified DC and timing accuracy is maintained for 1 year minimum.
|
|
| Power Requirements |
Voltage
|
|
100–240 VAC ±10% at 45-66 Hz; 100-120 VAC ±10% at 380-420 Hz; Automatic AC Voltage Selection
|
Max. Power Consumption
|
|
850 W/850 VA
|
|
| Environmental and Safety |
Temperature (Operating)
|
|
+5 °C to +40 °C including CD-RW/DVD-ROM drive
|
Temperature (Non-Operating)
|
|
–20 °C to +60 °C
|
Humidity (Operating)
|
|
5% to 80% relative humidity (non-condensing) up to +31 °C.
|
Humidity (Non-Operating)
|
|
5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F
|
Altitude (Operating)
|
|
Up to 10,000 ft. (3048 m) at or below +25 °C
|
Altitude (Non-Operating)
|
|
Up to 40,000 ft. (12,192 m)
|
Random Vibration (Operating)
|
|
0.5 grms overall level, 5 Hz to 500 Hz, 10 minutes in each of three orthogonal axes, 30 minutes total
|
Random Vibration (Non-Operating)
|
|
2.0 grms overall level, 5 Hz to 500 Hz, 10 minutes in each of three orthogonal axes, 30 minutes total
|
Functional Shock
|
|
20 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total
|
|
| Physical Dimensions |
Dimensions (HWD)
|
|
14"H x 18.4"W x 11.4"D (355 x 467 x 289 mm)
|
Weight
|
|
39.5 lbs. (18 kg)
|
Shipping Weight
|
|
28.2 kg; 62 lbs.
|
|
| Certifications |
Certifications
|
|
CE Compliant, UL and cUL listed; conforms to EN 61326-1, EN 61010-1, UL 61010-1 2nd edition, and CSA C22.2 No. 61010-1-04
|
|
| Warranty and Service |
Warranty and Service
|
|
3-year warranty; calibration recommended annually.
|
|
WavePro 725Zi
| Vertical System |
Analog Bandwidth @ 50 Ω (-3 dB)
|
|
2.5 GHz
|
Rise Time (typical)
|
|
150 ps
|
Input Channels
|
|
4
|
Bandwidth Limiters
|
|
20 MHz, 200 MHz
|
Input Impedance
|
|
50 Ω or 1 MΩ||15pF, 10 MΩ || 11 pF with supplied Probe
|
Input Coupling
|
|
1 MΩ: AC, DC, GND; 50 Ω: DC, GND
|
Maximum Input Voltage
|
|
50 Ω: ±5 Vrms
|
Channel-Channel Isolation ProLink Input
|
|
Not Applicable
|
Channel to Channel Isolation ProBus Input
|
|
100:1
|
Vertical Resolution
|
|
8 bits; up to 11 bits with enhanced resolution (ERES)
|
Sensitivity
|
|
50 Ω: 2 mV–1 V/div, fully variable (2-9.99 mV/div via zoom); 1 MΩ: 2 mV–10 V/div, fully variable
|
DC Gain Accuracy
|
|
±1.5% of full scale
|
Offset Range
|
|
50 Ω:
|
Offset Accuracy
|
|
±(1.5% of full scale + 1.0% of offset value + 1 mV)
|
|
| Horizontal System |
Timebases
|
|
Internal timebase common to 4 input channels; an external clock may be applied at the auxiliary input
|
Time/Division Range
|
|
20 ps/div–1000 s/div (RIS mode: 20 ps/div - 10 ns/div; Roll mode: up to 1000 s/div)
|
Clock Accuracy
|
|
< 1 ppm
|
Jitter Noise Floor
|
|
1 ps (typical)
|
Trigger and Interpolator Jitter
|
|
2 psrms (typical)
|
Sample Rate and Delay Time Accuracy
|
|
< 0.06 / SR + (1 ppm * Reading) (rms)
|
Channel-Channel Deskew Range
|
|
±9 x time/div. setting, 100 ms max., each channel
|
External Timebase Reference (Input)
|
|
10 MHz; 50 Ω impedance, applied at the rear input
|
External Timebase Reference (Output)
|
|
10 MHz; 50 Ω impedance, output at the rear
|
External Sample Clock
|
|
0.1 Hz-100 MHz, 50 Ω or 1 MΩ impedance, applied at the auxiliary input
|
|
| Acquisition System |
Single-Shot Sample Rate/Ch
|
|
40 GS/s on 2 Ch
|
Random Interleaved Sampling (RIS)
|
|
200 GS/s for repetitive signals (20 ps/div to 10 ns/div)
|
Maximum Trigger Rate
|
|
1,000,000 waveforms/second (in Sequence Mode, up to 4 channels)
|
Intersegment Time
|
|
1 μs
|
Standard Memory (4 Ch / 2 Ch) (Number of Segments)
|
|
10 M / 20 M
|
S - Memory Option
|
|
32 M / 64 M
|
M - Memory Option
|
|
64 M / 128 M
|
L - Memory Option
|
|
128 M / 256 M
|
|
| Acquisition Processing |
Averaging
|
|
Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps
|
Enhanced Resolution (ERES)
|
|
From 8.5 to 11 bits vertical resolution
|
Envelope (Extrema)
|
|
Envelope, floor, or roof for up to 1 million sweeps
|
Interpolation
|
|
Linear or Sin x/x
|
|
| Triggering System |
Modes
|
|
Normal, Auto, Single, and Stop
|
Sources
|
|
Any input channel, Aux, Aux/10, or line; slope and level unique to each source (except line trigger)
|
Coupling Mode
|
|
DC, AC, HFRej, LFRej
|
Pre-trigger Delay
|
|
0–100% of memory size (adjustable in 1% increments of 100 ns)
|
Post-trigger Delay
|
|
0–10,000 divisions in real time mode, limited at slower time/div settings or in roll mode
|
Hold-off by Time or Events
|
|
From 2 ns up to 20 s or from 1 to 99,999,999 events
|
Internal Trigger Range
|
|
±5 div from center
|
Trigger Sensitivity with Edge Trigger (Ch 1–4) ProBus Inputs
|
|
2 div @ < 2.5 GHz
|
Trigger Sensitivity with Edge Trigger (Ch 1–4) ProLink Inputs
|
|
Not Applicable
|
External Trigger Sensitivity
|
|
2 div @ < 1 GHz
|
External Trigger Input Range
|
|
Aux (±0.4 V); Aux/10 (±4 V)
|
Max. Trigger Frequency, SMART Trigger
|
|
2.0 GHz @ = 10 mV/div (minimum signal width setting 300 ps)
|
|
| Basic Triggers |
Edge/ Slope/ Line
|
|
Triggers when signal meets slope (positive, negative, or either) and level condition.
|
TV-Composite Video
|
|
Triggers NTSC or PAL with selectable line and field; HDTV (720p, 1080i, 1080p) with selectable frame rate (50 or 60 Hz) and Line; or CUSTOM with selectable Fields (1-8), Lines (up to 2000), Frame Rates (25, 30, 50, or 60 Hz), Interlacing (1:1, 2:1, 4:1, 8:1), or Synch Pulse Slope (Positive or Negative).
|
|
| SMART Triggers |
State or Edge Qualified
|
|
Triggers on any input source only if a defined state or edge occurred on another input source. Delay between sources is selectable by time or events.
|
Dropout
|
|
Triggers if signal drops out for longer than selected time between 1 ns and 20 s.
|
Pattern
|
|
Logic combination (AND, NAND, OR, NOR) of 5 inputs (4 channels and external trigger input). Each source can be high, low, or don’t care. The High and Low level can be selected independently. Triggers at start or end of the pattern.
|
|
| SMART Triggers with Exclusion Technology |
Glitch
|
|
Triggers on positive or negative glitches with widths selectable as low as 500 ps (depending on oscilloscope bandwidth) to 20 s, or on intermittent faults.
|
Width (Signal or Pattern)
|
|
Triggers on positive or negative widths with widths selectable as low as 200ps (depending on oscilloscope bandwidth) to 20 s, or on intermittent faults.
|
Interval (Signal or Pattern)
|
|
Triggers on intervals selectable between 1 ns and 20 s.
|
Timeout (State/Edge Qualified)
|
|
Triggers on any source if a given state (or transition edge) has occurred on another source.
|
Runt
|
|
Trigger on positive or negative runts defined by two voltage limits and two time limits. Select between 1 ns and 20 ns.
|
Slew Rate
|
|
Trigger on edge rates. Select limits for dV, dt, and slope. Select edge limits between 1 ns and 20 ns.
|
"A" Trigger List
|
|
Edge, Window, Width, Glitch, Pattern, Pattern State, State, Dropout, Interval, Runt, Slew Rate, Serial Data (optional I2C, SPI, UART/RS-232, CAN, LIN, FlexRay)
|
"B" Trigger List
|
|
Edge
|
Exclusion Triggering
|
|
Trigger on intermittent faults by specifying the expected behavior and triggering when that condition is not met
|
Holdoff Between Sequential Triggers
|
|
Arming = Serial & Triggering = Anything, then min. time between events defined by serial pattern length
|
|
| Cascade (Sequence) Triggering |
Capability
|
|
Arm on “A” event, then Trigger on “B” event. Or Arm on “A” event, then Qualify on “B” event, and Trigger on “C” event. Or Arm on “A” event, then Qualify on “B” then “C” event, and Trigger on “D” event
|
Types
|
|
A or B event: Edge, Glitch, Width, Window, Dropout, Interval, Runt, Slew Rate, or Pattern (analog) C or D event: Edge or Pattern
|
Holdoff
|
|
Delay between A and B, B and C, C and D, are all selectable by time or number of events
|
Reset
|
|
Reset between A and B, B and C, C and D, are all selectable in time
|
|
| High Speed Serial Protocol Triggering |
Data Rates
|
|
100 Mb/s - 1.25 Gb/s
|
Pattern Length
|
|
80 bits, NRZ or 8b10b
|
Clock and Data Outputs
|
|
400mVp-p (typical) AC coupled
|
Clock Recovery Jitter
|
|
2 ps rms + 0.3% Unit Interval rms for PRBS data patterns with 50% transition density (Typical)
|
Clock Recovery Tracking/ Acquisition Range
|
|
50 Mb/s - 1.25 Gb/s
|
Hardware Clock Recovery Loop BW
|
|
PLL Loop BW = Fbaud/5500, 100 Mb/s to 1.25 Gb/s (Typical)
|
|
| Low Speed Serial Protocol Triggering (Optional) |
Optionally available
|
|
I2C, SPI (SPI, SSPI, SIOP), UART-RS232, CAN, LIN, FlexRay
|
|
| Color Waveform Display |
Type
|
|
Color 15.3" flat panel TFT-Active Matrix LCD with high resolution touch screen
|
Resolution
|
|
WXGA; 1280 x 768 pixels
|
Number of traces
|
|
Display a maximum of 8 traces. Simultaneously display channel, zoom, memory and math traces.
|
Grid Styles
|
|
Auto, Single, Dual, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y
|
Waveform Representation
|
|
Sample dots joined, or sample dots only
|
|
| Internal Waveform Memory |
Internal Waveform Memory
|
|
4 active waveform memory traces (M1-M4) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity.
|
|
| WaveStream™ Fast Viewing Mode |
Intensity
|
|
256 Intensity Levels, 1–100% adjustable via front panel control
|
Number of Channels
|
|
up to 4 simultaneously
|
Max Sampling Rate
|
|
40 GS/s (20 GS/s for WavePro 710Zi without WPZi-1GHZ-4X20GS option)
|
Waveforms
|
|
up to 2500 Waveforms/ second
|
|
| Automatic Setup |
Auto Setup
|
|
Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals
|
Find Vertical Scale
|
|
Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range
|
|
| Probes |
Probes
|
|
Qty. (4) ÷10 Passive Probes
|
Probe System: ProBus
|
|
Probus (and ProLink on 4-6 GHz models). Automatically detects and supports a variety of compatible probes
|
Scale Factors
|
|
Automatically or manually selected depending on probe used
|
Calibration Output
|
|
1kHz square wave, 1Vp-p (typical), output to probe hook
|
|
| Analog Persistence Display |
Analog and Color-Graded Persistence
|
|
Variable saturation levels; stores each trace’s persistence data in memory
|
Trace Selection
|
|
Activate persistence on all or any combination of traces
|
Sweep Display Modes
|
|
All accumulated, or all accumulated with last trace highlighted
|
Persistence Types
|
|
Select analog, color, or three-dimensional
|
Persistence Aging
|
|
Select from 500 ms to infinity
|
|
| Setup and Waveform Storage |
Front Panel and Instrument Status
|
|
Store to the internal hard drive or to a USB-connected peripheral device.
|
|
| High Speed Digitizer Output (Option) |
Type
|
|
LeCroy LSIB
|
Transfer Rate
|
|
Up to 325 MB/s (Typical)
|
Output Protocol
|
|
PCI Express, Gen 1 (4 lanes utilized for data transfer)
|
Control Protocol
|
|
TCP/IP
|
Command Set
|
|
Via Windows Automation, or via LeCroy Remote Command Set
|
|
| Processor/CPU |
Type
|
|
Intel® CoreTM 2 Quad, 2.5 GHz (or better)
|
Processor Memory
|
|
4 GB standard, up to 8 GB optional
|
Operating System
|
|
Microsoft Windows® Vista Business Edition (64-bit) with SP1
|
Oscilloscope Operating Software
|
|
Entire instrument including any installed optional applications packages operates within a single (X-Stream) Windows application
|
Real Time Clock
|
|
Date and time displayed with waveform an in hardcopy files. SNTP support to synchronize to precision internal clocks.
|
|
| Zoom Expansion Traces |
Zoom Expansion Traces
|
|
Display up to 4 Zoom and 8 Math/Zoom traces
|
|
| Interface |
Remote Control
|
|
Via Windows Automation, or via LeCroy Remote Command Set
|
GPIB Port (optional)
|
|
Supports IEEE – 488.2
|
LSIB Port (optional)
|
|
Supports PCIe Gen1 x4 protocol with LeCroy supplied API
|
USB Device Port (optional)
|
|
Type-B
|
Ethernet Port
|
|
Supports 10/100/1000 BaseT Ethernet interface (RJ45 port)
|
USB Ports
|
|
minimum 6 total (incl. 3 front panel) USB 2.0 ports support Windows compatible devices
|
External Monitor Port
|
|
15-pin D-Type WXGA compatible to support customer-supplied external monitor. DVI connector to support LeCroy Zi-EXTDISP-15 additional touch screen display accessory. Includes support for extended desktop operation with optional LeCroy or other second monitor
|
Serial Port
|
|
2 standard
|
Peripheral Bus
|
|
LeCroy LBUS standard
|
|
| Auxiliary Input |
Signal Types
|
|
Select External Trigger
|
Coupling
|
|
50 Ω: DC; 1 MΩ: AC, DC, GND
|
Max. Input Voltage
|
|
50 Ω: 5 Vrms; 1 MΩ: 250 V (Peak AC < 10 kHz + DC)
|
|
| Auxiliary Output |
Signal Types
|
|
Select from calibrator, control signals or Off
|
Calibrator Signal
|
|
5 Hz–5 MHz square wave or DC level; 0.0 to 500 mV into 50 Ω (0–1 V into 1 MΩ)
|
Control Signals
|
|
Trigger enabled, trigger out, pass/fail status
|
|
| General |
Auto Calibration
|
|
Ensures specified DC and timing accuracy is maintained for 1 year minimum.
|
|
| Power Requirements |
Voltage
|
|
100–240 VAC ±10% at 45-66 Hz; 100-120 VAC ±10% at 380-420 Hz; Automatic AC Voltage Selection
|
Max. Power Consumption
|
|
850 W/850 VA
|
|
| Environmental and Safety |
Temperature (Operating)
|
|
+5 °C to +40 °C including CD-RW/DVD-ROM drive
|
Temperature (Non-Operating)
|
|
–20 °C to +60 °C
|
Humidity (Operating)
|
|
5% to 80% relative humidity (non-condensing) up to +31 °C.
|
Humidity (Non-Operating)
|
|
5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F
|
Altitude (Operating)
|
|
Up to 10,000 ft. (3048 m) at or below +25 °C
|
Altitude (Non-Operating)
|
|
Up to 40,000 ft. (12,192 m)
|
Random Vibration (Operating)
|
|
0.5 grms overall level, 5 Hz to 500 Hz, 10 minutes in each of three orthogonal axes, 30 minutes total
|
Random Vibration (Non-Operating)
|
|
2.0 grms overall level, 5 Hz to 500 Hz, 10 minutes in each of three orthogonal axes, 30 minutes total
|
Functional Shock
|
|
20 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total
|
|
| Physical Dimensions |
Dimensions (HWD)
|
|
14"H x 18.4"W x 11.4"D (355 x 467 x 289 mm)
|
Weight
|
|
39.5 lbs. (18 kg)
|
Shipping Weight
|
|
28.2 kg; 62 lbs.
|
|
| Certifications |
Certifications
|
|
CE Compliant, UL and cUL listed; conforms to EN 61326-1, EN 61010-1, UL 61010-1 2nd edition, and CSA C22.2 No. 61010-1-04
|
|
| Warranty and Service |
Warranty and Service
|
|
3-year warranty; calibration recommended annually.
|
|
WavePro 735Zi
| Vertical System |
Analog Bandwidth @ 50 Ω (-3 dB)
|
|
3.5 GHz
|
Rise Time (typical)
|
|
120 ps
|
Input Channels
|
|
4
|
Bandwidth Limiters
|
|
20 MHz, 200 MHz
|
Input Impedance
|
|
50 Ω or 1 MΩ||15pF, 10 MΩ || 11 pF with supplied Probe
|
Input Coupling
|
|
1 MΩ: AC, DC, GND; 50 Ω: DC, GND
|
Maximum Input Voltage
|
|
50 Ω: ±5 Vrms
|
Channel-Channel Isolation ProLink Input
|
|
Not Applicable
|
Channel to Channel Isolation ProBus Input
|
|
> 100:1 up to 2.5 GHz, > 30:1 from 2.5 GHz to 3.5 GHz
|
Vertical Resolution
|
|
8 bits; up to 11 bits with enhanced resolution (ERES)
|
Sensitivity
|
|
50 O: 2 mV–1 V/div, fully variable (2-9.99 mV/div via zoom); 1 MO: 2 mV–10 V/div, fully variable
|
DC Gain Accuracy
|
|
±1.5% of full scale
|
Offset Range
|
|
50 Ω:
|
Offset Accuracy
|
|
±(1.5% of full scale + 1.0% of offset value + 1 mV)
|
|
| Horizontal System |
Timebases
|
|
Internal timebase common to 4 input channels; an external clock may be applied at the auxiliary input
|
Time/Division Range
|
|
20 ps/div–1000 s/div (RIS mode: 20 ps/div - 10 ns/div; Roll mode: up to 1000 s/div)
|
Clock Accuracy
|
|
< 1 ppm
|
Jitter Noise Floor
|
|
800 fs (typical)
|
Trigger and Interpolator Jitter
|
|
2 psrms (typical)
|
Sample Rate and Delay Time Accuracy
|
|
< 0.06 / SR + (1 ppm * Reading) (rms)
|
Channel-Channel Deskew Range
|
|
±9 x time/div. setting, 100 ms max., each channel
|
External Timebase Reference (Input)
|
|
10 MHz; 50 Ω impedance, applied at the rear input
|
External Timebase Reference (Output)
|
|
10 MHz; 50 Ω impedance, output at the rear
|
External Sample Clock
|
|
0.1 Hz-100 MHz, 50 Ω or 1 MΩ impedance, applied at the auxiliary input
|
|
| Acquisition System |
Single-Shot Sample Rate/Ch
|
|
40 GS/s on 2 Ch
|
Random Interleaved Sampling (RIS)
|
|
200 GS/s for repetitive signals (20 ps/div to 10 ns/div)
|
Maximum Trigger Rate
|
|
1,000,000 waveforms/second (in Sequence Mode, up to 4 channels)
|
Intersegment Time
|
|
1 μs
|
Standard Memory (4 Ch / 2 Ch) (Number of Segments)
|
|
10 M / 20 M
|
S - Memory Option
|
|
32 M / 64 M
|
M - Memory Option
|
|
64 M / 128 M
|
L - Memory Option
|
|
128 M / 256 M
|
|
| Acquisition Processing |
Averaging
|
|
Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps
|
Enhanced Resolution (ERES)
|
|
From 8.5 to 11 bits vertical resolution
|
Envelope (Extrema)
|
|
Envelope, floor, or roof for up to 1 million sweeps
|
Interpolation
|
|
Linear or Sin x/x
|
|
| Triggering System |
Modes
|
|
Normal, Auto, Single, and Stop
|
Sources
|
|
Any input channel, Aux, Aux/10, or line; slope and level unique to each source (except line trigger)
|
Coupling Mode
|
|
DC, AC, HFRej, LFRej
|
Pre-trigger Delay
|
|
0–100% of memory size (adjustable in 1% increments of 100 ns)
|
Post-trigger Delay
|
|
0–10,000 divisions in real time mode, limited at slower time/div settings or in roll mode
|
Hold-off by Time or Events
|
|
From 2 ns up to 20 s or from 1 to 99,999,999 events
|
Internal Trigger Range
|
|
±5 div from center
|
Trigger Sensitivity with Edge Trigger (Ch 1–4) ProBus Inputs
|
|
2 div @ < 3.5 GHz
|
Trigger Sensitivity with Edge Trigger (Ch 1–4) ProLink Inputs
|
|
Not Applicable
|
External Trigger Sensitivity
|
|
2 div @ < 1 GHz
|
External Trigger Input Range
|
|
Aux (±0.4 V); Aux/10 (±4 V)
|
Max. Trigger Frequency, SMART Trigger
|
|
2.0 GHz @ = 10 mV/div (minimum signal width setting 250 ps)
|
|
| Basic Triggers |
Edge/ Slope/ Line
|
|
Triggers when signal meets slope (positive, negative, or either) and level condition.
|
TV-Composite Video
|
|
Triggers NTSC or PAL with selectable line and field; HDTV (720p, 1080i, 1080p) with selectable frame rate (50 or 60 Hz) and Line; or CUSTOM with selectable Fields (1-8), Lines (up to 2000), Frame Rates (25, 30, 50, or 60 Hz), Interlacing (1:1, 2:1, 4:1, 8:1), or Synch Pulse Slope (Positive or Negative).
|
|
| SMART Triggers |
State or Edge Qualified
|
|
Triggers on any input source only if a defined state or edge occurred on another input source. Delay between sources is selectable by time or events.
|
Dropout
|
|
Triggers if signal drops out for longer than selected time between 1 ns and 20 s.
|
Pattern
|
|
Logic combination (AND, NAND, OR, NOR) of 5 inputs (4 channels and external trigger input). Each source can be high, low, or don’t care. The High and Low level can be selected independently. Triggers at start or end of the pattern.
|
|
| SMART Triggers with Exclusion Technology |
Glitch
|
|
Triggers on positive or negative glitches with widths selectable as low as 500 ps (depending on oscilloscope bandwidth) to 20 s, or on intermittent faults.
|
Width (Signal or Pattern)
|
|
Triggers on positive or negative widths with widths selectable as low as 200ps (depending on oscilloscope bandwidth) to 20 s, or on intermittent faults.
|
Interval (Signal or Pattern)
|
|
Triggers on intervals selectable between 1 ns and 20 s.
|
Timeout (State/Edge Qualified)
|
|
Triggers on any source if a given state (or transition edge) has occurred on another source.
|
Runt
|
|
Trigger on positive or negative runts defined by two voltage limits and two time limits. Select between 1 ns and 20 ns.
|
Slew Rate
|
|
Trigger on edge rates. Select limits for dV, dt, and slope. Select edge limits between 1 ns and 20 ns.
|
"A" Trigger List
|
|
Edge, Window, Width, Glitch, Pattern, Pattern State, State, Dropout, Interval, Runt, Slew Rate, Serial Data (optional I2C, SPI, UART/RS-232, CAN, LIN, FlexRay)
|
"B" Trigger List
|
|
Edge
|
Exclusion Triggering
|
|
Trigger on intermittent faults by specifying the expected behavior and triggering when that condition is not met
|
Holdoff Between Sequential Triggers
|
|
Arming = Serial & Triggering = Anything, then min. time between events defined by serial pattern length
|
|
| Cascade (Sequence) Triggering |
Capability
|
|
Arm on “A” event, then Trigger on “B” event. Or Arm on “A” event, then Qualify on “B” event, and Trigger on “C” event. Or Arm on “A” event, then Qualify on “B” then “C” event, and Trigger on “D” event
|
Types
|
|
A or B event: Edge, Glitch, Width, Window, Dropout, Interval, Runt, Slew Rate, or Pattern (analog) C or D event: Edge or Pattern
|
Holdoff
|
|
Delay between A and B, B and C, C and D, are all selectable by time or number of events
|
Reset
|
|
Reset between A and B, B and C, C and D, are all selectable in time
|
|
| High Speed Serial Protocol Triggering |
Data Rates
|
|
100 Mb/s - 1.25 Gb/s
|
Pattern Length
|
|
80 bits, NRZ or 8b10b
|
Clock and Data Outputs
|
|
400mVp-p (typical) AC coupled
|
Clock Recovery Jitter
|
|
2 ps rms + 0.3% Unit Interval rms for PRBS data patterns with 50% transition density (Typical)
|
Clock Recovery Tracking/ Acquisition Range
|
|
50 Mb/s - 1.25 Gb/s
|
Hardware Clock Recovery Loop BW
|
|
PLL Loop BW = Fbaud/5500, 100 Mb/s to 1.25 Gb/s (Typical)
|
|
| Low Speed Serial Protocol Triggering (Optional) |
Optionally available
|
|
I2C, SPI (SPI, SSPI, SIOP), UART-RS232, CAN, LIN, FlexRay
|
|
| Color Waveform Display |
Type
|
|
Color 15.3" flat panel TFT-Active Matrix LCD with high resolution touch screen
|
Resolution
|
|
WXGA; 1280 x 768 pixels
|
Number of traces
|
|
Display a maximum of 8 traces. Simultaneously display channel, zoom, memory and math traces.
|
Grid Styles
|
|
Auto, Single, Dual, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y
|
Waveform Representation
|
|
Sample dots joined, or sample dots only
|
|
| Internal Waveform Memory |
Internal Waveform Memory
|
|
4 active waveform memory traces (M1-M4) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity.
|
|
| WaveStream™ Fast Viewing Mode |
Intensity
|
|
256 Intensity Levels, 1–100% adjustable via front panel control
|
Number of Channels
|
|
up to 4 simultaneously
|
Max Sampling Rate
|
|
40 GS/s (20 GS/s for WavePro 710Zi without WPZi-1GHZ-4X20GS option)
|
Waveforms
|
|
up to 2500 Waveforms/ second
|
|
| Automatic Setup |
Auto Setup
|
|
Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals
|
Find Vertical Scale
|
|
Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range
|
|
| Probes |
Probes
|
|
Qty. (4) ÷10 Passive Probes
|
Probe System: ProBus
|
|
Probus (and ProLink on 4-6 GHz models). Automatically detects and supports a variety of compatible probes
|
Scale Factors
|
|
Automatically or manually selected depending on probe used
|
Calibration Output
|
|
1kHz square wave, 1Vp-p (typical), output to probe hook
|
|
| Analog Persistence Display |
Analog and Color-Graded Persistence
|
|
Variable saturation levels; stores each trace’s persistence data in memory
|
Trace Selection
|
|
Activate persistence on all or any combination of traces
|
Sweep Display Modes
|
|
All accumulated, or all accumulated with last trace highlighted
|
Persistence Types
|
|
Select analog, color, or three-dimensional
|
Persistence Aging
|
|
Select from 500 ms to infinity
|
|
| Setup and Waveform Storage |
Front Panel and Instrument Status
|
|
Store to the internal hard drive or to a USB-connected peripheral device.
|
|
| High Speed Digitizer Output (Option) |
Type
|
|
LeCroy LSIB
|
Transfer Rate
|
|
Up to 325 MB/s (Typical)
|
Output Protocol
|
|
PCI Express, Gen 1 (4 lanes utilized for data transfer)
|
Control Protocol
|
|
TCP/IP
|
Command Set
|
|
Via Windows Automation, or via LeCroy Remote Command Set
|
|
| Processor/CPU |
Type
|
|
Intel® CoreTM 2 Quad, 2.5 GHz (or better)
|
Processor Memory
|
|
4 GB standard, up to 8 GB optional
|
Operating System
|
|
Microsoft Windows® Vista Business Edition (64-bit) with SP1
|
Oscilloscope Operating Software
|
|
Entire instrument including any installed optional applications packages operates within a single (X-Stream) Windows application
|
Real Time Clock
|
|
Date and time displayed with waveform an in hardcopy files. SNTP support to synchronize to precision internal clocks.
|
|
| Zoom Expansion Traces |
Zoom Expansion Traces
|
|
Display up to 4 Zoom and 8 Math/Zoom traces
|
|
| Interface |
Remote Control
|
|
Via Windows Automation, or via LeCroy Remote Command Set
|
GPIB Port (optional)
|
|
Supports IEEE – 488.2
|
LSIB Port (optional)
|
|
Supports PCIe Gen1 x4 protocol with LeCroy supplied API
|
USB Device Port (optional)
|
|
Type-B
|
Ethernet Port
|
|
Supports 10/100/1000 BaseT Ethernet interface (RJ45 port)
|
USB Ports
|
|
minimum 6 total (incl. 3 front panel) USB 2.0 ports support Windows compatible devices
|
External Monitor Port
|
|
15-pin D-Type WXGA compatible to support customer-supplied external monitor. DVI connector to support LeCroy Zi-EXTDISP-15 additional touch screen display accessory. Includes support for extended desktop operation with optional LeCroy or other second monitor
|
Serial Port
|
|
2 standard
|
Peripheral Bus
|
|
LeCroy LBUS standard
|
|
| Auxiliary Input |
Signal Types
|
|
Select External Trigger
|
Coupling
|
|
50 Ω: DC; 1 MΩ: AC, DC, GND
|
Max. Input Voltage
|
|
50 Ω: 5 Vrms; 1 MΩ: 250 V (Peak AC < 10 kHz + DC)
|
|
| Auxiliary Output |
Signal Types
|
|
Select from calibrator, control signals or Off
|
Calibrator Signal
|
|
5 Hz–5 MHz square wave or DC level; 0.0 to 500 mV into 50 Ω (0–1 V into 1 MΩ)
|
Control Signals
|
|
Trigger enabled, trigger out, pass/fail status
|
|
| General |
Auto Calibration
|
|
Ensures specified DC and timing accuracy is maintained for 1 year minimum.
|
|
| Power Requirements |
Voltage
|
|
100–240 VAC ±10% at 45-66 Hz; 100-120 VAC ±10% at 380-420 Hz; Automatic AC Voltage Selection
|
Max. Power Consumption
|
|
850 W/850 VA
|
|
| Environmental and Safety |
Temperature (Operating)
|
|
+5 °C to +40 °C including CD-RW/DVD-ROM drive
|
Temperature (Non-Operating)
|
|
–20 °C to +60 °C
|
Humidity (Operating)
|
|
5% to 80% relative humidity (non-condensing) up to +31 °C.
|
Humidity (Non-Operating)
|
|
5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F
|
Altitude (Operating)
|
|
Up to 10,000 ft. (3048 m) at or below +25 °C
|
Altitude (Non-Operating)
|
|
Up to 40,000 ft. (12,192 m)
|
Random Vibration (Operating)
|
|
0.5 grms overall level, 5 Hz to 500 Hz, 10 minutes in each of three orthogonal axes, 30 minutes total
|
Random Vibration (Non-Operating)
|
|
2.0 grms overall level, 5 Hz to 500 Hz, 10 minutes in each of three orthogonal axes, 30 minutes total
|
Functional Shock
|
|
20 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total
|
|
| Physical Dimensions |
Dimensions (HWD)
|
|
14"H x 18.4"W x 11.4"D (355 x 467 x 289 mm)
|
Weight
|
|
39.5 lbs. (18 kg)
|
Shipping Weight
|
|
28.2 kg; 62 lbs.
|
|
| Certifications |
Certifications
|
|
CE Compliant, UL and cUL listed; conforms to EN 61326-1, EN 61010-1, UL 61010-1 2nd edition, and CSA C22.2 No. 61010-1-04
|
|
| Warranty and Service |
Warranty and Service
|
|
3-year warranty; calibration recommended annually.
|
|
WavePro 740Zi
| Vertical System |
Analog Bandwidth @ 50 Ω (-3 dB)
|
|
4 GHz
|
Rise Time (typical)
|
|
105 ps
|
Input Channels
|
|
4
|
Bandwidth Limiters
|
|
20 MHz, 200 MHz
|
Input Impedance
|
|
50 Ω or 1 MΩ||15pF, 10 MΩ || 11 pF with supplied Probe
|
Input Coupling
|
|
1 MΩ: AC, DC, GND; 50 Ω: DC, GND
|
Maximum Input Voltage
|
|
50 Ω (ProBus): ±5 Vrms
|
Channel-Channel Isolation ProLink Input
|
|
> 200:1 up to 2 GHz, > 50:1 from 2 GHz to 4 GHz
|
Channel to Channel Isolation ProBus Input
|
|
> 100:1 up to 2.5 GHz, > 30:1 from 2.5 GHz to 3.5 GHz
|
Vertical Resolution
|
|
8 bits; up to 11 bits with enhanced resolution (ERES)
|
Sensitivity
|
|
50 O: 2 mV–1 V/div, fully variable (2-9.99 mV/div via zoom); 1 MO: 2 mV–10 V/div, fully variable
|
DC Gain Accuracy
|
|
±1.5% of full scale
|
Offset Range
|
|
50 Ω:
|
Offset Accuracy
|
|
±(1.5% of full scale + 1.0% of offset value + 1 mV)
|
|
| Horizontal System |
Timebases
|
|
Internal timebase common to 4 input channels; an external clock may be applied at the auxiliary input
|
Time/Division Range
|
|
20 ps/div–1000 s/div (RIS mode: 20 ps/div - 10 ns/div; Roll mode: up to 1000 s/div)
|
Clock Accuracy
|
|
< 1 ppm
|
Jitter Noise Floor
|
|
750 fs (typical)
|
Trigger and Interpolator Jitter
|
|
1 psrms (typical)
|
Sample Rate and Delay Time Accuracy
|
|
< 0.06 / SR + (1 ppm * Reading) (rms)
|
Channel-Channel Deskew Range
|
|
±9 x time/div. setting, 100 ms max., each channel
|
External Timebase Reference (Input)
|
|
10 MHz; 50 Ω impedance, applied at the rear input
|
External Timebase Reference (Output)
|
|
10 MHz; 50 Ω impedance, output at the rear
|
External Sample Clock
|
|
0.1 Hz-100 MHz, 50 Ω or 1 MΩ impedance, applied at the auxiliary input
|
|
| Acquisition System |
Single-Shot Sample Rate/Ch
|
|
40 GS/s on 2 Ch
|
Random Interleaved Sampling (RIS)
|
|
200 GS/s for repetitive signals (20 ps/div to 10 ns/div)
|
Maximum Trigger Rate
|
|
1,000,000 waveforms/second (in Sequence Mode, up to 4 channels)
|
Intersegment Time
|
|
1 μs
|
Standard Memory (4 Ch / 2 Ch) (Number of Segments)
|
|
10 M / 20 M
|
S - Memory Option
|
|
32 M / 64 M
|
M - Memory Option
|
|
64 M / 128 M
|
L - Memory Option
|
|
128 M / 256 M
|
|
| Acquisition Processing |
Averaging
|
|
Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps
|
Enhanced Resolution (ERES)
|
|
From 8.5 to 11 bits vertical resolution
|
Envelope (Extrema)
|
|
Envelope, floor, or roof for up to 1 million sweeps
|
Interpolation
|
|
Linear or Sin x/x
|
|
| Triggering System |
Modes
|
|
Normal, Auto, Single, and Stop
|
Sources
|
|
Any input channel, Aux, Aux/10, or line; slope and level unique to each source (except line trigger)
|
Coupling Mode
|
|
DC, AC, HFRej, LFRej
|
Pre-trigger Delay
|
|
0–100% of memory size (adjustable in 1% increments of 100 ns)
|
Post-trigger Delay
|
|
0–10,000 divisions in real time mode, limited at slower time/div settings or in roll mode
|
Hold-off by Time or Events
|
|
From 2 ns up to 20 s or from 1 to 99,999,999 events
|
Internal Trigger Range
|
|
±5 div from center
|
Trigger Sensitivity with Edge Trigger (Ch 1–4) ProBus Inputs
|
|
2 div @ < 3.5 GHz
|
Trigger Sensitivity with Edge Trigger (Ch 1–4) ProLink Inputs
|
|
2 div @ < 4 GHz
|
External Trigger Sensitivity
|
|
2 div @ < 1 GHz
|
External Trigger Input Range
|
|
Aux (±0.4 V); Aux/10 (±4 V)
|
Max. Trigger Frequency, SMART Trigger
|
|
2.0 GHz @ = 10 mV/div
|
|
| Basic Triggers |
Edge/ Slope/ Line
|
|
Triggers when signal meets slope (positive, negative, or either) and level condition.
|
TV-Composite Video
|
|
Triggers NTSC or PAL with selectable line and field; HDTV (720p, 1080i, 1080p) with selectable frame rate (50 or 60 Hz) and Line; or CUSTOM with selectable Fields (1-8), Lines (up to 2000), Frame Rates (25, 30, 50, or 60 Hz), Interlacing (1:1, 2:1, 4:1, 8:1), or Synch Pulse Slope (Positive or Negative).
|
|
| SMART Triggers |
State or Edge Qualified
|
|
Triggers on any input source only if a defined state or edge occurred on another input source. Delay between sources is selectable by time or events.
|
Dropout
|
|
Triggers if signal drops out for longer than selected time between 1 ns and 20 s.
|
Pattern
|
|
Logic combination (AND, NAND, OR, NOR) of 5 inputs (4 channels and external trigger input). Each source can be high, low, or don’t care. The High and Low level can be selected independently. Triggers at start or end of the pattern.
|
|
| SMART Triggers with Exclusion Technology |
Glitch
|
|
Triggers on positive or negative glitches with widths selectable as low as 500 ps (depending on oscilloscope bandwidth) to 20 s, or on intermittent faults.
|
Width (Signal or Pattern)
|
|
Triggers on positive or negative widths with widths selectable as low as 200ps (depending on oscilloscope bandwidth) to 20 s, or on intermittent faults.
|
Interval (Signal or Pattern)
|
|
Triggers on intervals selectable between 1 ns and 20 s.
|
Timeout (State/Edge Qualified)
|
|
Triggers on any source if a given state (or transition edge) has occurred on another source.
|
Runt
|
|
Trigger on positive or negative runts defined by two voltage limits and two time limits. Select between 1 ns and 20 ns.
|
Slew Rate
|
|
Trigger on edge rates. Select limits for dV, dt, and slope. Select edge limits between 1 ns and 20 ns.
|
"A" Trigger List
|
|
Edge, Window, Width, Glitch, Pattern, Pattern State, State, Dropout, Interval, Runt, Slew Rate, Serial Data (optional I2C, SPI, UART/RS-232, CAN, LIN, FlexRay)
|
"B" Trigger List
|
|
Edge
|
Exclusion Triggering
|
|
Trigger on intermittent faults by specifying the expected behavior and triggering when that condition is not met
|
Holdoff Between Sequential Triggers
|
|
Arming = Serial & Triggering = Anything, then min. time between events defined by serial pattern length
|
|
| Cascade (Sequence) Triggering |
Capability
|
|
Arm on “A” event, then Trigger on “B” event. Or Arm on “A” event, then Qualify on “B” event, and Trigger on “C” event. Or Arm on “A” event, then Qualify on “B” then “C” event, and Trigger on “D” event
|
Types
|
|
A or B event: Edge, Glitch, Width, Window, Dropout, Interval, Runt, Slew Rate, or Pattern (analog) C or D event: Edge or Pattern
|
Holdoff
|
|
Delay between A and B, B and C, C and D, are all selectable by time or number of events
|
Reset
|
|
Reset between A and B, B and C, C and D, are all selectable in time
|
|
| High Speed Serial Protocol Triggering |
Data Rates
|
|
100 Mb/s - 3.125 Gb/s
|
Pattern Length
|
|
80 bits, NRZ or 8b10b
|
Clock and Data Outputs
|
|
400mVp-p (typical) AC coupled
|
Clock Recovery Jitter
|
|
2 ps rms + 0.3% Unit Interval rms for PRBS data patterns with 50% transition density (Typical)
|
Clock Recovery Tracking/ Acquisition Range
|
|
50 Mb/s - 2.7 Gb/s
|
Hardware Clock Recovery Loop BW
|
|
PLL Loop BW = Fbaud/5500, 100 Mb/s to 1.25 Gb/s (Typical)
|
|
| Low Speed Serial Protocol Triggering (Optional) |
Optionally available
|
|
I2C, SPI (SPI, SSPI, SIOP), UART-RS232, CAN, LIN, FlexRay
|
|
| Color Waveform Display |
Type
|
|
Color 15.3" flat panel TFT-Active Matrix LCD with high resolution touch screen
|
Resolution
|
|
WXGA; 1280 x 768 pixels
|
Number of traces
|
|
Display a maximum of 8 traces. Simultaneously display channel, zoom, memory and math traces.
|
Grid Styles
|
|
Auto, Single, Dual, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y
|
Waveform Representation
|
|
Sample dots joined, or sample dots only
|
|
| Internal Waveform Memory |
Internal Waveform Memory
|
|
4 active waveform memory traces (M1-M4) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity.
|
|
| WaveStream™ Fast Viewing Mode |
Intensity
|
|
256 Intensity Levels, 1–100% adjustable via front panel control
|
Number of Channels
|
|
up to 4 simultaneously
|
Max Sampling Rate
|
|
40 GS/s (20 GS/s for WavePro 710Zi without WPZi-1GHZ-4X20GS option)
|
Waveforms
|
|
up to 2500 Waveforms/ second
|
|
| Automatic Setup |
Auto Setup
|
|
Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals
|
Find Vertical Scale
|
|
Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range
|
|
| Probes |
Probes
|
|
Qty. (4) ÷10 Passive Probes
|
Probe System: ProBus
|
|
Probus (and ProLink on 4-6 GHz models). Automatically detects and supports a variety of compatible probes
|
Scale Factors
|
|
Automatically or manually selected depending on probe used
|
Calibration Output
|
|
1kHz square wave, 1Vp-p (typical), output to probe hook
|
|
| Analog Persistence Display |
Analog and Color-Graded Persistence
|
|
Variable saturation levels; stores each trace’s persistence data in memory
|
Trace Selection
|
|
Activate persistence on all or any combination of traces
|
Sweep Display Modes
|
|
All accumulated, or all accumulated with last trace highlighted
|
Persistence Types
|
|
Select analog, color, or three-dimensional
|
Persistence Aging
|
|
Select from 500 ms to infinity
|
|
| Setup and Waveform Storage |
Front Panel and Instrument Status
|
|
Store to the internal hard drive or to a USB-connected peripheral device.
|
|
| High Speed Digitizer Output (Option) |
Type
|
|
LeCroy LSIB
|
Transfer Rate
|
|
Up to 325 MB/s (Typical)
|
Output Protocol
|
|
PCI Express, Gen 1 (4 lanes utilized for data transfer)
|
Control Protocol
|
|
TCP/IP
|
Command Set
|
|
Via Windows Automation, or via LeCroy Remote Command Set
|
|
| Processor/CPU |
Type
|
|
Intel® CoreTM 2 Quad, 2.5 GHz (or better)
|
Processor Memory
|
|
4 GB standard, up to 8 GB optional
|
Operating System
|
|
Microsoft Windows® Vista Business Edition (64-bit) with SP1
|
Oscilloscope Operating Software
|
|
Entire instrument including any installed optional applications packages operates within a single (X-Stream) Windows application
|
Real Time Clock
|
|
Date and time displayed with waveform an in hardcopy files. SNTP support to synchronize to precision internal clocks.
|
|
| Zoom Expansion Traces |
Zoom Expansion Traces
|
|
Display up to 4 Zoom and 8 Math/Zoom traces
|
|
| Interface |
Remote Control
|
|
Via Windows Automation, or via LeCroy Remote Command Set
|
GPIB Port (optional)
|
|
Supports IEEE – 488.2
|
LSIB Port (optional)
|
|
Supports PCIe Gen1 x4 protocol with LeCroy supplied API
|
USB Device Port (optional)
|
|
Type-B
|
Ethernet Port
|
|
Supports 10/100/1000 BaseT Ethernet interface (RJ45 port)
|
USB Ports
|
|
minimum 6 total (incl. 3 front panel) USB 2.0 ports support Windows compatible devices
|
External Monitor Port
|
|
15-pin D-Type WXGA compatible to support customer-supplied external monitor. DVI connector to support LeCroy Zi-EXTDISP-15 additional touch screen display accessory. Includes support for extended desktop operation with optional LeCroy or other second monitor
|
Serial Port
|
|
2 standard
|
Peripheral Bus
|
|
LeCroy LBUS standard
|
|
| Auxiliary Input |
Signal Types
|
|
Select External Trigger
|
Coupling
|
|
50 Ω: DC; 1 MΩ: AC, DC, GND
|
Max. Input Voltage
|
|
50 Ω: 5 Vrms; 1 MΩ: 250 V (Peak AC < 10 kHz + DC)
|
|
| Auxiliary Output |
Signal Types
|
|
Select from calibrator, control signals or Off
|
Calibrator Signal
|
|
5 Hz–5 MHz square wave or DC level; 0.0 to 500 mV into 50 Ω (0–1 V into 1 MΩ)
|
Control Signals
|
|
Trigger enabled, trigger out, pass/fail status
|
|
| General |
Auto Calibration
|
|
Ensures specified DC and timing accuracy is maintained for 1 year minimum.
|
|
| Power Requirements |
Voltage
|
|
100–240 VAC ±10% at 45-66 Hz; 100-120 VAC ±10% at 380-420 Hz; Automatic AC Voltage Selection
|
Max. Power Consumption
|
|
850 W/850 VA
|
|
| Environmental and Safety |
Temperature (Operating)
|
|
+5 °C to +40 °C including CD-RW/DVD-ROM drive
|
Temperature (Non-Operating)
|
|
–20 °C to +60 °C
|
Humidity (Operating)
|
|
5% to 80% relative humidity (non-condensing) up to +31 °C.
|
Humidity (Non-Operating)
|
|
5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F
|
Altitude (Operating)
|
|
Up to 10,000 ft. (3048 m) at or below +25 °C
|
Altitude (Non-Operating)
|
|
Up to 40,000 ft. (12,192 m)
|
Random Vibration (Operating)
|
|
0.5 grms overall level, 5 Hz to 500 Hz, 10 minutes in each of three orthogonal axes, 30 minutes total
|
Random Vibration (Non-Operating)
|
|
2.0 grms overall level, 5 Hz to 500 Hz, 10 minutes in each of three orthogonal axes, 30 minutes total
|
Functional Shock
|
|
20 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total
|
|
| Physical Dimensions |
Dimensions (HWD)
|
|
14"H x 18.4"W x 11.4"D (355 x 467 x 289 mm)
|
Weight
|
|
39.5 lbs. (18 kg)
|
Shipping Weight
|
|
28.2 kg; 62 lbs.
|
|
| Certifications |
Certifications
|
|
CE Compliant, UL and cUL listed; conforms to EN 61326-1, EN 61010-1, UL 61010-1 2nd edition, and CSA C22.2 No. 61010-1-04
|
|
| Warranty and Service |
Warranty and Service
|
|
3-year warranty; calibration recommended annually.
|
|
WavePro 760Zi
| Vertical System |
Analog Bandwidth @ 50 Ω (-3 dB)
|
|
6 GHz
|
Rise Time (typical)
|
|
70 ps
|
Input Channels
|
|
4
|
Bandwidth Limiters
|
|
20 MHz, 200 MHz
|
Input Impedance
|
|
50 Ω or 1 MΩ||15pF, 10 MΩ || 11 pF with supplied Probe
|
Input Coupling
|
|
1 MΩ: AC, DC, GND; 50 Ω: DC, GND
|
Maximum Input Voltage
|
|
50 Ω (ProBus): ±5 Vrms
|
Channel-Channel Isolation ProLink Input
|
|
> 200:1 up to 2 GHz, > 50:1 from 2 GHz to 4 GHz, > 20:1 from 4 GHz to 6 GHz
|
Channel to Channel Isolation ProBus Input
|
|
> 100:1 up to 2.5 GHz, > 30:1 from 2.5 GHz to 3.5 GHz
|
Vertical Resolution
|
|
8 bits; up to 11 bits with enhanced resolution (ERES)
|
Sensitivity
|
|
50 Ω: 2 mV–1 V/div, fully variable (2-9.99 mV/div via zoom); 1 MΩ: 2 mV–10 V/div, fully variable
|
DC Gain Accuracy
|
|
±1.5% of full scale
|
Offset Range
|
|
50 Ω:
|
Offset Accuracy
|
|
±(1.5% of full scale + 1.0% of offset value + 1 mV)
|
|
| Horizontal System |
Timebases
|
|
Internal timebase common to 4 input channels; an external clock may be applied at the auxiliary input
|
Time/Division Range
|
|
20 ps/div–1000 s/div (RIS mode: 20 ps/div - 10 ns/div; Roll mode: up to 1000 s/div)
|
Clock Accuracy
|
|
< 1 ppm
|
Jitter Noise Floor
|
|
560 fs (typical)
|
Trigger and Interpolator Jitter
|
|
1 psrms (typical)
|
Sample Rate and Delay Time Accuracy
|
|
< 0.06 / SR + (1 ppm * Reading) (rms)
|
Channel-Channel Deskew Range
|
|
±9 x time/div. setting, 100 ms max., each channel
|
External Timebase Reference (Input)
|
|
10 MHz; 50 Ω impedance, applied at the rear input
|
External Timebase Reference (Output)
|
|
10 MHz; 50 Ω impedance, output at the rear
|
External Sample Clock
|
|
0.1 Hz-100 MHz, 50 Ω or 1 MΩ impedance, applied at the auxiliary input
|
|
| Acquisition System |
Single-Shot Sample Rate/Ch
|
|
40 GS/s on 2 Ch
|
Random Interleaved Sampling (RIS)
|
|
200 GS/s for repetitive signals (20 ps/div to 10 ns/div)
|
Maximum Trigger Rate
|
|
1,000,000 waveforms/second (in Sequence Mode, up to 4 channels)
|
Intersegment Time
|
|
1 μs
|
Standard Memory (4 Ch / 2 Ch) (Number of Segments)
|
|
10 M / 20 M
|
S - Memory Option
|
|
32 M / 64 M
|
M - Memory Option
|
|
64 M / 128 M
|
L - Memory Option
|
|
128 M / 256 M
|
|
| Acquisition Processing |
Averaging
|
|
Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps
|
Enhanced Resolution (ERES)
|
|
From 8.5 to 11 bits vertical resolution
|
Envelope (Extrema)
|
|
Envelope, floor, or roof for up to 1 million sweeps
|
Interpolation
|
|
Linear or Sin x/x
|
|
| Triggering System |
Modes
|
|
Normal, Auto, Single, and Stop
|
Sources
|
|
Any input channel, Aux, Aux/10, or line; slope and level unique to each source (except line trigger)
|
Coupling Mode
|
|
DC, AC, HFRej, LFRej
|
Pre-trigger Delay
|
|
0–100% of memory size (adjustable in 1% increments of 100 ns)
|
Post-trigger Delay
|
|
0–10,000 divisions in real time mode, limited at slower time/div settings or in roll mode
|
Hold-off by Time or Events
|
|
From 2 ns up to 20 s or from 1 to 99,999,999 events
|
Internal Trigger Range
|
|
±5 div from center
|
Trigger Sensitivity with Edge Trigger (Ch 1–4) ProBus Inputs
|
|
2 div @ < 3.5 GHz
|
Trigger Sensitivity with Edge Trigger (Ch 1–4) ProLink Inputs
|
|
2 div @ < 6 GHz
|
External Trigger Sensitivity
|
|
2 div @ < 1 GHz
|
External Trigger Input Range
|
|
Aux (±0.4 V); Aux/10 (±4 V)
|
Max. Trigger Frequency, SMART Trigger
|
|
2.0 GHz @ = 10 mV/div
|
|
| Basic Triggers |
Edge/ Slope/ Line
|
|
Triggers when signal meets slope (positive, negative, or either) and level condition.
|
TV-Composite Video
|
|
Triggers NTSC or PAL with selectable line and field; HDTV (720p, 1080i, 1080p) with selectable frame rate (50 or 60 Hz) and Line; or CUSTOM with selectable Fields (1-8), Lines (up to 2000), Frame Rates (25, 30, 50, or 60 Hz), Interlacing (1:1, 2:1, 4:1, 8:1), or Synch Pulse Slope (Positive or Negative).
|
|
| SMART Triggers |
State or Edge Qualified
|
|
Triggers on any input source only if a defined state or edge occurred on another input source. Delay between sources is selectable by time or events.
|
Dropout
|
|
Triggers if signal drops out for longer than selected time between 1 ns and 20 s.
|
Pattern
|
|
Logic combination (AND, NAND, OR, NOR) of 5 inputs (4 channels and external trigger input). Each source can be high, low, or don’t care. The High and Low level can be selected independently. Triggers at start or end of the pattern.
|
|
| SMART Triggers with Exclusion Technology |
Glitch
|
|
Triggers on positive or negative glitches with widths selectable as low as 500 ps (depending on oscilloscope bandwidth) to 20 s, or on intermittent faults.
|
Width (Signal or Pattern)
|
|
Triggers on positive or negative widths with widths selectable as low as 200ps (depending on oscilloscope bandwidth) to 20 s, or on intermittent faults.
|
Interval (Signal or Pattern)
|
|
Triggers on intervals selectable between 1 ns and 20 s.
|
Timeout (State/Edge Qualified)
|
|
Triggers on any source if a given state (or transition edge) has occurred on another source.
|
Runt
|
|
Trigger on positive or negative runts defined by two voltage limits and two time limits. Select between 1 ns and 20 ns.
|
Slew Rate
|
|
Trigger on edge rates. Select limits for dV, dt, and slope. Select edge limits between 1 ns and 20 ns.
|
"A" Trigger List
|
|
Edge, Window, Width, Glitch, Pattern, Pattern State, State, Dropout, Interval, Runt, Slew Rate, Serial Data (optional I2C, SPI, UART/RS-232, CAN, LIN, FlexRay)
|
"B" Trigger List
|
|
Edge
|
Exclusion Triggering
|
|
Trigger on intermittent faults by specifying the expected behavior and triggering when that condition is not met
|
Holdoff Between Sequential Triggers
|
|
Arming = Serial & Triggering = Anything, then min. time between events defined by serial pattern length
|
|
| Cascade (Sequence) Triggering |
Capability
|
|
Arm on “A” event, then Trigger on “B” event. Or Arm on “A” event, then Qualify on “B” event, and Trigger on “C” event. Or Arm on “A” event, then Qualify on “B” then “C” event, and Trigger on “D” event
|
Types
|
|
A or B event: Edge, Glitch, Width, Window, Dropout, Interval, Runt, Slew Rate, or Pattern (analog) C or D event: Edge or Pattern
|
Holdoff
|
|
Delay between A and B, B and C, C and D, are all selectable by time or number of events
|
Reset
|
|
Reset between A and B, B and C, C and D, are all selectable in time
|
|
| High Speed Serial Protocol Triggering |
Data Rates
|
|
100 Mb/s - 3.125 Gb/s
|
Pattern Length
|
|
80 bits, NRZ or 8b10b
|
Clock and Data Outputs
|
|
400mVp-p (typical) AC coupled
|
Clock Recovery Jitter
|
|
2 ps rms + 0.3% Unit Interval rms for PRBS data patterns with 50% transition density (Typical)
|
Clock Recovery Tracking/ Acquisition Range
|
|
50 Mb/s - 2.7 Gb/s
|
Hardware Clock Recovery Loop BW
|
|
PLL Loop BW = Fbaud/5500, 100 Mb/s to 1.25 Gb/s (Typical)
|
|
| Low Speed Serial Protocol Triggering (Optional) |
Optionally available
|
|
I2C, SPI (SPI, SSPI, SIOP), UART-RS232, CAN, LIN, FlexRay
|
|
| Color Waveform Display |
Type
|
|
Color 15.3" flat panel TFT-Active Matrix LCD with high resolution touch screen
|
Resolution
|
|
WXGA; 1280 x 768 pixels
|
Number of traces
|
|
Display a maximum of 8 traces. Simultaneously display channel, zoom, memory and math traces.
|
Grid Styles
|
|
Auto, Single, Dual, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y
|
Waveform Representation
|
|
Sample dots joined, or sample dots only
|
|
| Internal Waveform Memory |
Internal Waveform Memory
|
|
4 active waveform memory traces (M1-M4) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity.
|
|
| WaveStream™ Fast Viewing Mode |
Intensity
|
|
256 Intensity Levels, 1–100% adjustable via front panel control
|
Number of Channels
|
|
up to 4 simultaneously
|
Max Sampling Rate
|
|
40 GS/s (20 GS/s for WavePro 710Zi without WPZi-1GHZ-4X20GS option)
|
Waveforms
|
|
up to 2500 Waveforms/ second
|
|
| Automatic Setup |
Auto Setup
|
|
Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals
|
Find Vertical Scale
|
|
Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range
|
|
| Probes |
Probes
|
|
Qty. (4) ÷10 Passive Probes
|
Probe System: ProBus
|
|
Probus (and ProLink on 4-6 GHz models). Automatically detects and supports a variety of compatible probes
|
Scale Factors
|
|
Automatically or manually selected depending on probe used
|
Calibration Output
|
|
1kHz square wave, 1Vp-p (typical), output to probe hook
|
|
| Analog Persistence Display |
Analog and Color-Graded Persistence
|
|
Variable saturation levels; stores each trace’s persistence data in memory
|
Trace Selection
|
|
Activate persistence on all or any combination of traces
|
Sweep Display Modes
|
|
All accumulated, or all accumulated with last trace highlighted
|
Persistence Types
|
|
Select analog, color, or three-dimensional
|
Persistence Aging
|
|
Select from 500 ms to infinity
|
|
| Setup and Waveform Storage |
Front Panel and Instrument Status
|
|
Store to the internal hard drive or to a USB-connected peripheral device.
|
|
| High Speed Digitizer Output (Option) |
Type
|
|
LeCroy LSIB
|
Transfer Rate
|
|
Up to 325 MB/s (Typical)
|
Output Protocol
|
|
PCI Express, Gen 1 (4 lanes utilized for data transfer)
|
Control Protocol
|
|
TCP/IP
|
Command Set
|
|
Via Windows Automation, or via LeCroy Remote Command Set
|
|
| Processor/CPU |
Type
|
|
Intel® CoreTM 2 Quad, 2.5 GHz (or better)
|
Processor Memory
|
|
4 GB standard, up to 8 GB optional
|
Operating System
|
|
Microsoft Windows® Vista Business Edition (64-bit) with SP1
|
Oscilloscope Operating Software
|
|
Entire instrument including any installed optional applications packages operates within a single (X-Stream) Windows application
|
Real Time Clock
|
|
Date and time displayed with waveform an in hardcopy files. SNTP support to synchronize to precision internal clocks.
|
|
| Zoom Expansion Traces |
Zoom Expansion Traces
|
|
Display up to 4 Zoom and 8 Math/Zoom traces
|
|
| Interface |
Remote Control
|
|
Via Windows Automation, or via LeCroy Remote Command Set
|
GPIB Port (optional)
|
|
Supports IEEE – 488.2
|
LSIB Port (optional)
|
|
Supports PCIe Gen1 x4 protocol with LeCroy supplied API
|
USB Device Port (optional)
|
|
Type-B
|
Ethernet Port
|
|
Supports 10/100/1000 BaseT Ethernet interface (RJ45 port)
|
USB Ports
|
|
minimum 6 total (incl. 3 front panel) USB 2.0 ports support Windows compatible devices
|
External Monitor Port
|
|
15-pin D-Type WXGA compatible to support customer-supplied external monitor. DVI connector to support LeCroy Zi-EXTDISP-15 additional touch screen display accessory. Includes support for extended desktop operation with optional LeCroy or other second monitor
|
Serial Port
|
|
2 standard
|
Peripheral Bus
|
|
LeCroy LBUS standard
|
|
| Auxiliary Input |
Signal Types
|
|
Select External Trigger
|
Coupling
|
|
50 Ω: DC; 1 MO: AC, DC, GND
|
Max. Input Voltage
|
|
50 Ω: 5 Vrms; 1 MO: 250 V (Peak AC < 10 kHz + DC)
|
|
| Auxiliary Output |
Signal Types
|
|
Select from calibrator, control signals or Off
|
Calibrator Signal
|
|
5 Hz–5 MHz square wave or DC level; 0.0 to 500 mV into 50 Ω (0–1 V into 1 MΩ)
|
Control Signals
|
|
Trigger enabled, trigger out, pass/fail status
|
|
| General |
Auto Calibration
|
|
Ensures specified DC and timing accuracy is maintained for 1 year minimum.
|
|
| Power Requirements |
Voltage
|
|
100–240 VAC ±10% at 45-66 Hz; 100-120 VAC ±10% at 380-420 Hz; Automatic AC Voltage Selection
|
Max. Power Consumption
|
|
850 W/850 VA
|
|
| Environmental and Safety |
Temperature (Operating)
|
|
+5 °C to +40 °C including CD-RW/DVD-ROM drive
|
Temperature (Non-Operating)
|
|
–20 °C to +60 °C
|
Humidity (Operating)
|
|
5% to 80% relative humidity (non-condensing) up to +31 °C.
|
Humidity (Non-Operating)
|
|
5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F
|
Altitude (Operating)
|
|
Up to 10,000 ft. (3048 m) at or below +25 °C
|
Altitude (Non-Operating)
|
|
Up to 40,000 ft. (12,192 m)
|
Random Vibration (Operating)
|
|
0.5 grms overall level, 5 Hz to 500 Hz, 10 minutes in each of three orthogonal axes, 30 minutes total
|
Random Vibration (Non-Operating)
|
|
2.0 grms overall level, 5 Hz to 500 Hz, 10 minutes in each of three orthogonal axes, 30 minutes total
|
Functional Shock
|
|
20 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total
|
|
| Physical Dimensions |
Dimensions (HWD)
|
|
14"H x 18.4"W x 11.4"D (355 x 467 x 289 mm)
|
Weight
|
|
39.5 lbs. (18 kg)
|
Shipping Weight
|
|
28.2 kg; 62 lbs.
|
|
| Certifications |
Certifications
|
|
CE Compliant, UL and cUL listed; conforms to EN 61326-1, EN 61010-1, UL 61010-1 2nd edition, and CSA C22.2 No. 61010-1-04
|
|
| Warranty and Service |
Warranty and Service
|
|
3-year warranty; calibration recommended annually.
|
|
Memory Options
| | WPZi-L-128 | 4ch Large Memory for WavePro Zi. Includes an additional 4 GB of RAM (8 GB total) | | WPZi-M-64 | 4ch Medium Memory for WavePro Zi. Includes an additional 4 GB of RAM (8 GB total) | | WPZi-S-32 | 4ch Small Memory for WavePro Zi. Includes an additional 2 GB of RAM (4 GB total) | Serial Trigger and Decode
| | WPZi-8B10B D | 8b10b Decode Option for WavePro Zi Series Oscilloscopes | | WPZi-FlexrayBus TD | FlexRay Bus Trigger & Decode Option for WavePro Zi Series Oscilloscopes | | WPZi-FlexRayBus TDP | FlexRay Bus Trigger, Decode, and Physical Layer Test Option for WavePro Zi Series Oscilloscopes | | WPZi-HSPT | 50 Mb/s to 3.125 Gb/s High Speed Serial Trigger Option for 4-6 GHz Oscilloscopes & Disk Drive Analyzers | | WPZi-I2Cbus TD | I2C Bus Trigger & Decode Option for WavePro Zi Series Oscilloscopes | | WPZi-LINbus TD | LIN Bus Trigger & Decode Option for WavePro Zi Series Oscilloscopes | | WPZi-MSPT | 50 Mb/s to 1.25 Gb/s Medium Speed Serial Trigger Option for 2.5-3.5 GHz Oscilloscopes & Disk Drive Analyzers | | WPZi-SPIbus TD | SPI Bus Trigger & Decode Option for WavePro Zi Series Oscilloscopes | | WPZi-UART-RS232bus TD | UART and RS232 Bus Trigger & Decode Option for WavePro Zi Series Oscilloscopes | Serial Data Analysis
| | WPZi-SDAII | SDAII Analysis Package | Serial Data Communications Testing Software
| | QPHY-ENET | QualiPHY Ethernet Application Software | | QPHY-HDMI | QualiPHY Enabled HDMI Software Option (TF-HDMI-3.3V-QUADPAK required;WavePro 760Zi requires SDA II option) | | QPHY-PCIe | PCIe Gen1 Compliance and Development Software | | QPHY-SATA | QualiPHY Enabled SATA Software Option | | QPHY-USB | USB Application Software Package | | QPHY-UWB | WiMedia UWB Transmitter Measurement Software Option | | WPZi-SDM | Serial Data Mask Software Package for WavePro Zi Series | General Purpose Software
| | WPZi-AORM | Advanced Optical Recording Measurement Package for WavePro Zi Series | | WPZi-CBL-DE-EMBED | Remove cable effects from your measurements | | WPZi-EMC | EMC Pulse Parameter Software Package for WavePro Zi Series | | WPZi-ET-PMT | Electrical Telecom Pulse Mask Test Package for WavePro Zi Series | | WPZi-EYEDRII | Eye Doctor II Advanced Signal Integrity Tools for WavePro 7 Zi Oscilloscopes, SDA 7 Zi Serial Data Analyzers, and DDA 7 Zi Disk Drive Analyzers | | WPZi-SPECTRUM | Spectrum Analyzer and Advanced FFT Option for WavePro Zi Series | | WPZi-XDEV | Developer's Tool Kit Option for WavePro Zi Series | Digital Filtering Software
| | WPZi-DFP2 | Digital Filter Software Package for WavePro Zi Series | Data Storage Software
| | WPZi-DDM2 | Disk Drive Measurements Software Package for WavePro Zi Series | Jitter Analysis Software
| | WPZi-JTA2 | Jitter Timing and Analysis Software Package for WavePro Zi Series | CAN Bus Testing
| | WPZi-CANbus TD | CAN Bus Trigger & Decode Option for WavePro Zi Series Oscilloscopes | | WPZi-CANbus TDM | CAN Bus Trigger, Decode, and Measure Option for WavePro Zi Series Oscilloscopes | Mixed Signal Test Solutions
| | MS-250 | 250 MHz Maximum Input Frequency, 18 Channels, 10 Mpts/ch Mixed Signal Oscilloscope Option | | MS-500 | 500 MHz Maximum Input Frequency, 18 Channels, 50 Mpts/ch Mixed Signal Oscilloscope Option | | MS-500-36 | 250 MHz Maximum Input Frequency, 36 Channels, 25 Mpts/ch Mixed Signal Oscilloscope Option | | MSO-DLS-18 | Digital Lead Set, D0-D17 | | MSO-DLS-36 | Digital Lead Set, D18-D35 | | MSO-GND-EXTEND | MSO Ground Extenders | | MSO-GND-LEAD | MSO Flying Ground Lead | | MSO-LBUS | LeCroy Bus Cable | | MSO-MICTOR | Mictor Cable, D0-D35 | Communications Testing Fixtures
| | TF-DSQ | Probe Deskew and Calibration Fixture | | TF-ENET-B | 10/100/1000Base-T Compliance Test Fixture | | TF-ET | Telecom Adaptor Kit 100Ω, 120Ω, 75Ω | | TF-HDMI-3.3V-QUADPAK | HDMI Pull-Up Terminator Quad Pack – for Use with the Efficere ET-HDMI-TPS-S Test Fixture | | TF-SATA-C | SATA Compliance Test Fixture (*WavePro 7 Zi and WaveMaster 8 Zi class oscilloscopes require the SDA II software option; **20M memory required) | | TF-SATA-C-Kit | SATA Compliance Test Kit (*WavePro 7 Zi and WaveMaster 8 Zi class oscilloscopes require the SDA II software option; **20M memory required) | | TF-USB-B | USB 2.0 Testing Compliance Test Fixture | Differential Amplifiers
| | DA1855A | DA1855A, 100 MHz Differential Amplifier with fast over drive recovery, calibrated offset, and selectable LP filters | | DA1855A-PR2 | 2 Ch, 100 MHz Differential Amplifier with fast over drive recovery, calibrated offset, and selectable LP filters | | DA1855A-PR2-RM | Rack mountable version of the DA1855A-PR2 | Storage Devices
| | GPIB-2 | GPIB Option for LeCroy oscilloscope. Half-height card with custom connector. | | LSIB-1 | High speed PCIe Gen1 x4 digitizer output for LeCroy oscilloscope. Half-height card with custom connector | | WPZi-2-UPG-8GBRAM | Upgrade from 2 GB to 8 GB CPU RAM | | WPZi-200GB-HD | Upgrade from standard size hard drive to 200 GB hard drive | | WPZi-200GB-RHD-02 | Additional 200 GB Hard Drive for WPZi. Includes Windows Vista OS, LeCroy oscilloscope software and critical scope operational file duplicates. | | WPZi-4-UPG-8GBRAM | Upgrade from 4 GB to 8 GB CPU RAM | Miscellaneous Accessories
| | FRONT-COVER-1 | Replacement Protective Front Cover for WavePro Zi Series | | KYBD-1 | Keyboard | | LSIB-CABLE-3M | PCI Express x 4 3-meter cable with x4 cable connectors included | | LSIB-CABLE-7M | PCI Express x 4 7-meter cable with x4 cable connectors include | | LSIB-HOSTBOARD | PCI Express x4 Host Interface Board for desktop PC | | LSIB-HOSTCARD | PCI Express x1 Express Card Host Interface for laptop Express Card slot | | POUCH-1 | Replacement Accessory Pouch | Rackmounts, Carts and Cases
| | OC1021 | OC1021 scope cart is sturdy and mobile | | OC1024 | OC1024 scope cart is sturdy and mobile | | RACKMOUNT-1 | Rack-mount accessory for converting a WavePro Zi series oscilloscope to an 8U rack-mounted package | | WPZi-HARDCASE | Hard carrying case for all WavePro Zi Series oscilloscopes | | WPZi-SOFTCASE | Soft carrying case for all WavePro Zi Series oscilloscopes | Warranty & Calibration
| | WPZi-C5 | Five Year NIST Calibration | | WPZi-C5/MIL | Five Year MIL Calibration | | WPZi-CC | NIST Traceable Calibration | | WPZi-CCM | MIL STD Calibration | | WPZi-CCMIL | MIL Std. Traceable Calibration | | WPZi-EW | 1 Year Extended Warranty | | WPZi-EW2 | 2 Year Extended Warranty | | WPZi-T5 | Five Year Warranty & NIST Calibration | | WPZi-T5/MIL | Five Year Warranty & MIL Calibration |
Differential Probes
| | ADP300 | High-Voltage Active Differential Probe | | ADP305 | High-Voltage Differential Probes From LeCroy | | AP031 | 15 MHz Differential Probe | | AP033 | 500 MHz Active Differential Probe | | AP034 | 1 GHz Active Differential Probe | | D300A-AT | WaveLink 4 GHz Differential Probe with Adjustable Tip Module | | D310 | WaveLink 3.5 GHz Differential probe module 2.5V | | D320 | WaveLink 3.5 GHz Differential probe module 5V | | D350ST | WaveLink 4 GHz, 5 V Differential with Small Tip Module | | D500PT | WaveLink 6 GHz Differential Positioner Mounted Tip Module | | D600A-AT | WaveLink 7.5 GHz Differential Probe with Adjustable Tip Module | | D600ST | WaveLink 7 GHz Differential Probe with Small Tip Module (includes D6000ST-SI, D600ST-QC, D600ST-SP) | | D610 | WaveLink 6 GHz Differential probe module 2.5V | | D620 | WaveLink 6 GHz Differential probe module 5V | | Dx10-PT | Replacement Dx10-PT Tip with Qty. 4 Pogo Pin Tips and Qty. 2 Sockets | | Dx20-PT | Replacement Dx20-PT Tip with Qty. 4 Pogo Pin Tips and Qty. 2 Sockets | | WL-Pbus | WaveLink ProBus probe body = 3.5 GHz | | WL-PLink | WaveLink ProLink probe body >3.5 GHz | | WL300 | WaveLink ProBus Probe Body | | WL600 | WaveLink ProLink Probe Body | Active Voltage Probes
| | HFP2500 | 2.5 GHz Active Voltage Probe | Current Probes
| | AP015 | 30 Amps, 50MHz BW Current Probe - AC/DC, 50 Amp Peak Pulse | | CP030 | 30 Amps, 50 MHz BW Current Probe - AC/DC , 50 Amp Peak Pulse | | CP031 | 30 Amps, 100 MHz BW Current Probe - AC/DC , 50 Amp Peak Pulse | | CP150 | 150 Amps, 10 MHz BW Current Probe - AC/DC , 500 Amp Peak Pulse | | CP500 | 500 Amps, 2 MHz BW Current Probe - AC/DC , 700 Amp Peak | High Voltage Probes
| | PPE1.2KV | 10:1/100:1 200/300 MHz 5M Ohm/100M Ohm | | PPE20KV | 1000:1 100 MHz 100M Ohm High-Voltage Probe | | PPE2KV | 100:1 400 MHz 100M Ohm High Voltage Probe | | PPE4KV | 100:1 400 MHz 100M Ohm High-Voltage Probe | | PPE5KV | 100:1 400 MHz 100M Ohm High-Voltage Probe | | PPE6KV | 1000:1 400 MHz 5M Ohm High-Voltage Probe | Passive Probes
| | PP007-WR-1 | Passive Probe, 500 MHz, 2.5mm tip | | PP011-1 | PP011 Passive Probe | ZS Series High Impedance Active Probes
| | ZS1000 | 1 GHz, 1 MΩ, 0.9 pF Active Probe | | ZS1000-QUADPAK | Set of 4 ZS1000 Active Probes | | ZS1500 | 1.5 GHz, 1 MΩ, 0.9 pF Active Probe | | ZS1500-QUADPAK | Set of 4 ZS1500 Active Probes | Optical to Electrical Converters
| | OE425 | Short wavelength O/E Converter (500-870 nm) | | OE455 | Long wavelength O/E Converter (950-1630 nm) | | OE525 | Short wavelength O/E Converter (500-870 nm) | | OE555 | Long wavelength O/E converter | Probe Adapters
| | LPA-SMA-A | Pro-Link to SMA Adapter, new style | | LPA-SMA-KIT-A | Kit of Pro-Link to SMA Adapter, new style | Probe Parts and Kits
| | Dx10-QC | Replacement Quick Connect lead set for D310/D610 | | Dx10-SI | Replacement Solder tip lead set for D310/D610 | | Dx10-SP | Replacement Square Pin lead set for D310/D610 | | Dx20-QC | Replacement Quick Connect lead set for D320/D620 | | Dx20-SI | Replacement Solder tip lead set for D320/D620 | | Dx20-SP | Replacement Square Pin lead set for D320/D620 |
|
|
|
